Home > Laminate Flooring Information > Laminate Flooring Questions > From carpet to laminate flooring help?

From carpet to laminate flooring help?

i want to replace the old carpet to laminate flooring. can anyone provide me with a step by step guide on how to do this? i have also purchased some underlayment for laminate flooring to go along with the flooring.

Public Comments

  1. Rip up the old carpet Install underlayment put down sound barrier install laminate flooring per manufacturer's instructions
  2. Are you sure you want laminate? I've heard it does not last. If you do want it, I would ask where you buy it for a step by step guide. They may even have an instructional video on how to do it....good luck!
  3. http://www.doityourself.com/scat/flooring
  4. Installing laminate is pretty easy in most cases. Remove all base boards. Make sure the floor is clean. Role out your sound bearrier. Tape the seams using a wide masking tape. You'll need a laminate wood block to connect you laminate together. Your peices that end up next to the wall will have to be a little short to fit in place. In door ways lay a scrap piece upside down and take a saw and cut out door jams to your laminate fits under door jams. Hope this helps some. I've installed for years.
  5. Rip up the carpet in small sections and roll them up...carpet is heavy. Get out the knee-pads, a claw-hammer and a pair of plyers. You will need to spend several hours pulling out all the staples and tacks, the 'tackstrips' around the edges and any nails. Use floor leveling compound to level any holes or gaps. Cut and fit the underlayment carefully untill it all lays flat. Take the underlayment out completely and roll glue on the floor with a painters roller and tray. The nail or screw it down thoroughly. Mark the layout carefully on the floor with a pencil. You want to shift it around so that no row ends in less than half a tile. It is like a puzzle. Get the layout right before you start. You may want to measure the room and work it out on paper. Spread the glue with a notched trowel. Do the whole room at once, back-to-front. Lay in all the whole tiles after the glue sets up. Linoleum tiles will cut leasily with a utility knife if you warm them up with a plumbers torch first. When you are done, wipe up any glue squeeze-out with a wet rag before it dries. Start the floor off with a good coat of floor polish for a long life.
  6. remove baseboard and nails if any.Cut ur carpet in manageable rolls, rip it out.Do same with foam but scrape off any glued pieces that stuck. Then remove carpet tack from perimeter. Be careful. Some laminate floors are easier than others but follow manufacturers instructions, too much variation will only cause problems later. One thing to consider is the shape of the room, alot of angles increase the difficulty. Some cuts maybe difficult and some laminates are almost like a very thin layer of glass. (very Hard) Eats up saw blades if you're not careful. But best of luck to you!
  7. Take up carpet and pad, remove tack strips from floor, take up baseboards, sweep floor, put down underlayment, nail in place, put down sound barrier, put down laminate, replace baseboards, examine floor, now smile cause it's done. One thing to know, your house will seem cooler in the winter time because the laminate is a better cold conductor than carpet.
  8. the cheap laminates are junk, a waste of time and money. the good ones are amazingly tuff! Where ever you buy it from should be able to answer your questions and loan you a dvd or tape of how to do it. most manufacters have a web site with that info.After installing a bunch of it I'm sold on Wilsonart brand, tuff and installs easy.http://www.mairmg.com/wilsonart/homeowner/start.cfm
  9. i dont know
  10. Select your new flooring and follow manufacturers directions for installation.
  11. Home Depot, Lowes, even Flooring Companys would be glad to assist your needs. The advice is free so go with professional help in this case! Good luck and enjoy your new flooring!
  12. make sure your underlayment is llouan flooring your floor will come out alot better and will last alot longer.most people don't know aboout the louan.i know because that's what i used to replace my kitchen floor.i learned it from a pro.louan is very thin wood panels made for tile ,laminate linoleum,etc.
  13. Pull up carpet, put down underlayment, install laminate flooring over top. Don't get much easier that that.
  14. Tear up the carpet. Replace or repair any damaged or un level flooring. Purchase a high quality laminate flooring. Cut the laminate flooring very carefully. Use a high quality glue / adhesive and a 1/8 inch grooved trowel. Lay the flooring out and roll it back half way. Spread the glue / adhesive and replace the flooring. Use a heavy roller made just for laminate flooring and roll over the flooring. Just remember to take your time and be patient. It's not hard to do, but you may be best to hire someone to do this job. One wrong cut and you have wasted your laminate flooring which can cost a lot. You may want to use an underlayment as well. You can always go to the web site www.diy.com